Products

Handheld Scanners


Product Information

Model: NLS-HR100L-76
Product Category: Handheld Laser Imager Barcode Scanner
Data type: 1D Bar Codes
Reading Mode:
Laser Imager
Interface: RS232/USB-HID/KBW


Overview
The NLS-HR100L-76 is a hybrid Laser and Linear Imager scanner with a revolutionary engine with no moving parts, offering the benefits of both linear imager and laser technologies in the same device. Ideal for applications such as: retail, office, logistics, banking, and health.

Features

Sophisticated Technology
Armed with Newland’s technology, the NLS-HR100L-76 demonstrates unparalleled reading performance with superb motion tolerance.

Swift and Precise Scanning
A laser imager is built into the device to enable rapid and accurate capture of even poor quality barcodes.

Rugged Structure Design
The rugged design with no moving parts inside provides the durability needed for day-to-day scan-intensive use.


Specification

Performance

Image Sensor

650 nm visible bidirectional laser diode +/- 50nm

Symbologies

Code 128, EAN-13, EAN-8, Code 39, UPC-A, UPC-E, Codabar, Interleaved 2 of 5,
ISBN, Code 93, UCC/EAN-128, GS1 Databar, Full ASII, Trioptic, etc.

Precision

≥ 3mil

Scan Angle**

Pitch      ±55° @ 0° Roll and 0° Skew
Roll       ±25° @ 0° Pitch and 0° Skew
Skew       ±65° @ 0° Roll and 0° Pitch

Symbol Contrast

≥10%

Scan Rate

300 scans per second

Interface

RS-232, USB, Keyboard, Compatible MetrOPOS (COMPATIBLE DRIVE).

Field Width

Between 25mm and 400mm, depending on the density of the bar code.

Cable and Operations System

Cable 1,8m - 3,0m, compatible with all operation system.

Depth of Scan Field

Between 0mm and 630mm, depending on the density of the bar code (including codes 10mils and 13mils).

Illumination

0 ~ 100,000 LUX

Mechanical/ Electrical

Dimensions (L x W x H)

156.0 * 95.0 * 71.0 mm

Weight

105g

Notification

Beep (12 tones or silent) and LED indicator (Red and Green)

Power Adaptor

Output: DC5V, 1.5A Input: AC100~240V, 50~60Hz

Current

Maximum Current

150mA

Operating Current

120mA

Standby Current

45mA

Power Consumption

Operation:0,75W Standby: 0,55W

Environment

Operate Temperature

-20°C to 60°C

Storage Temperature

-40°C to 85°C

Humidity

0 ~ 95% (non-condensing)

Static Discharge

± 4 kV (Contact discharge);± 8 kV (Air discharge)

Drop

1.5 m drops to concrete

Sealing

IP42

MTBF

100,000 (one hundred thousand) hours

Certifications

FCC Part15 Class B, CE EMC/EMI Class B

Safety

IEC/EN 60825-1 Safety of laser products, Class 1, CDRH Class II, IEC 60950/FCC Class B

**Test Condition:
Code 39, 3 Bytes; Resolution=10mil; W:N=2.5:1; PCS=0.8; Barcode Height=40mm; Scan Distance=210mm; T=23℃; Illumination= 200LUX


*Specifications are subject to change without notice*



  Document Name Size Document Type
1 HR100L-76 Datasheet 309 KB Datasheet
2 HR100L-76 Test Resport 181 KB Test Resport


1. How to confirm the types of your equipment, X+? X? or other type?
A. X+ type(EM2027 series, last number of serial number is "X+"), supported interface types: USB-DataPipe, USB Com Port Emuation, HID-KBW,RS232.
X type(EM2100 series,last number of serial Number is "X"), supported interface types: USB-DataPipe, USB Com Port Emuation, HID-KBW,RS232.

2. How to confirm whether the driver has been installed successfully?
A. First, confirm the equipment had connected to PC and the equipment operating normally.
Open: Control Panel> Device Manager> Universal Serial Bus Controller,
 If there is "Newland USB Datapipe to series Device" said connection is "USB Com Port Emuation"--COM.
 If there is "Newland USB DataPipe Device" said connection is "USB-DataPipe".
 If there is yellow "!" before the equipment, delete the equipment, and then scan detection hardware changes,  Wait for the system to automatically install the new drivers finished.

3. Whether it is necessary upgrade the driver of USB-Datapipe from the old version to the new v1.2 USB driver (vcomctrl v1.2.exe)?
A. The new driver support USB Interface of X+ : USB-DataPipe/ USB Com Port Emuation/HID-KBW. If the users of X series, had developed their own application through the USB SDK, recommendations are not updated to the latest driver.

4. If you have installed v1.2 USB driver, how to connect by USB-Datapipe?
A. If your equipment is X+ series, read the set code of USB-Datapipe.(You can download The Manual of Settings Code free from this website.) If your equipment is X series, first you should close USB to COM serve, open Control Panel> Tools> Services, find "Bulk to Serial service", select properties: select stop, Startup Type: Manual.

5. After installed the new driver, how to find out the COM port corresponding to the USB Com Port Emuation?
A. Open Start> all the procedures>vcomctrl>vcomctrl, you can find the number of the COM port there.

6. Why QuickSet can not connect the equipment through USB after installed v1.2 driver?
A. Confirm FAQ-1 driver has installed correctly --> Check out the number of COM port of FAQ-4 --> Confirmed equipment has been launched. Open the Quickset, select the right COM port,manual detection. If the detection failed, you can choose one of the following ways to solve the problem:

i.Check out whether swich to HID-KBW and have set Non-HID-KBW when read The Manual of Settings Code. Change and connect it again.

ii. If it connect through COM before, open "File>PC comm... > USB>OK" in Quickset, try whether it work.

iii. Close Quickset, close connection then open Control Panel> Tools> Services, find "Bulk to Serial service", select properties: select stop, and then start it again. Connect the equipment, open Quickset, try connection through COM.

iv. Close Quickset, close connection. Reboot the equipment, open Quickset, connect it again.







Applicable Accessories
Programming Guide A manual for user who can scans the pre-printed barcodes to define the configuration, By using accessories provided, scan all kinds of barcodes defined by customers.

Stand

STD100

The STD100 stand allows the HR100 to operate in hands-free mode and also doubled as an excellent accessory to rest the scanner when not in use.

Flex Cable
CBL037R This cable connect to the RS232 port of HR100 with a RJ45 port.
With a standard female RS232 port to connect to standard male RS232 port.
With a power port to accept power adapter supply.
CBL024U This cable connect to the USB Slave port of HR100 with a RJ45 port.
With a standard USB Slave port to connect to standard USB Host port.
CBL013P This cable connect to the KBW port of HR100 with a RJ45 port.With a PS/2 Host port.

Power
K5AA0500050W1UV-1
  • HR100 power adapter needed when using cable CBL037R, not included with the cable. Output: 5V/0.5A,3 Input: AC 100V-240V, 5-~60Hz, includes 3 jack-plugs (Euro,US,UK).





NEWS

Newland President Ms. Wang Jing joined China-Germany Economic Advisory Committee CEO Roundtable
More »
Season II Overseas Exhibition Start Now
More »
Newland release the first 2D-barcode decoder chip on the world wide scale
More »
Newland and Datalogic sign the Cooperative Strategy Framework Agreement
In November 11th, Fujian Newland Computer Co., LTD. and Datalogic SpA.(Italy) formally sign the Cooperative Strategy Framework Agreement in Beijing International Hotel.

More »